CONFIDENTIAL Listing of FC1000III GN6 Parameters
|
Parameter |
Setting |
Value |
Explanation |
|
0000 |
00100011 |
bit 5 |
= 1 metric/inch option |
|
|
|
|
= 0 metric only |
|
0001 |
00001000 |
|
|
|
0002 |
00100001 |
|
|
|
0003 |
10011010 |
bit 4 |
= 1 runtime clock displayed. |
|
|
|
|
= 0 runtime clock not displayed. |
|
|
|
|
Note: Clock data in parameters 57, 58, 59 - clock data clears if machine on less than 6 minutes. |
|
|
|
bit 7 |
= 1 P.C. parameters displayed. |
|
|
|
|
= 0 P.C. parameters not displayed. |
|
0005 |
00000010 |
bit 1 |
= 1 enables C axes. |
|
0006 |
10110001 |
bit 5 |
= 0 ignore servo off signal. |
|
|
|
|
= 1 recognizes servo off signal. |
|
|
|
bit 6 |
= 0 normal handling of M30 code. |
|
0007 |
11110010 |
bit 7 |
= 0 automatic drift compensation off. |
|
|
|
bit 5 |
= 1 reference point return uses special G codes. |
|
00001001 |
bit 3 |
= 0 powers up in G91 mode |
|
|
|
|
|
= 1 powers up in G90 mode |
|
|
|
bit 7 |
= 0 LF CR CR codes are punched as EOB in ISO code |
|
|
|
|
= 1 LF codes are punched as EOB in ISO code |
|
0010 |
00000010 |
|
|
|
0011 |
01000000 |
bit 5 |
= 0 decelerate when limit switch opens. |
|
|
|
|
= 1 decelerate when limit switch closes. |
|
0012 |
00000100 |
bits 4-7 |
determine that reference counter uses grid method |
|
0013 |
00010000 |
|
|
|
0014 |
00010001 |
|
X axis DMR (detect multiplying ratio - limit 10,000 counts) |
|
0015 |
00010001 |
|
Y axis DMR (detect multiplying ratio - limit 10,000 counts) |
|
0016 |
01110111 |
|
T axis DMR (detect multiplying ratio - limit 10,000 counts) |
|
0017 |
01110011 |
|
C axis DMR (detect multiplying ratio - limit 10,000 counts) |
|
0018 |
00000011 |
|
|
|
0019 |
00010000 |
|
sets time to respond to M code |
|
0020 |
00001111 |
|
C axis related |
|
0021 |
00011011 |
|
|
|
0024 |
00000000 |
bit 4 |
= 0 mass editing using 0-9999 is enabled |
|
0026 |
00010000 |
|
|
|
0027 |
4 |
|
X axis CMR (command multiplying ratio) |
|
0028 |
4 |
|
Y axis CMR (command multiplying ratio) |
|
0029 |
2 |
|
T axis CMR (command multiplying ratio) |
|
0030 |
20 |
|
C axis CMR (command multiplying ratio) |
|
0036-0056 |
00000000 |
|
|
|
----- |
|
runtime clock - hours |
|
|
----- |
|
runtime clock - minutes |
|
|
----- |
|
runtime clock - seconds |
|
|
|
|
|
Note#1: Param. 3.4 permits display of clock |
|
|
|
|
Note#2: Reading clears if machine not on a minimum of 6 minutes |
|
0060 |
0 |
|
clutch off timer for nibble (TPF 10) |
|
0061 |
0 |
|
clutch on signal off time (*PE to PFB) |
|
0070 |
100 |
|
X axis - in position deadband |
|
0071 |
100 |
|
Y axis - in position deadband |
|
0072 |
200 |
|
T axis - in position deadband |
|
0073 |
100 |
|
C axis - in position deadband |
|
0074 |
500 |
|
X axis - max following error when stopped |
|
0075 |
500 |
|
Y axis - max following error when stopped |
|
0076 |
500 |
|
T axis - max following error when stopped |
|
0077 |
3000 |
|
C axis - max following error when stopped |
|
0078 |
3000 |
|
X axis - max following error when moving |
|
0079 |
3000 |
|
Y axis - max following error when moving |
|
0080 |
12000 |
|
T axis - max following error when moving |
|
0081 |
20000 |
|
C axis - max following error when moving |
|
0082 |
----- |
|
X axis grid shift (home position offset) - varies |
|
0083 |
----- |
|
Y axis grid shift (home position offset) - varies |
|
0084 |
----- |
|
T axis grid shift (home position offset) - varies |
|
0085 |
----- |
|
C1 (4th axis) grid shift (home position offset) varies |
|
0347 |
----- |
|
C2 (5th axis) grid shift (home position offset) varies |
|
|
|
|
Note: Offsets measured in detect units. 1 detect unit =.0005 inch. Lower number moves hole closer to edge of sheet - must power down and back up to register change. |
|
0086 |
3584 |
|
X axis servo loop gain multiplier |
|
0087 |
3584 |
|
Y axis servo loop gain multiplier |
|
0088 |
896 |
|
T axis servo loop gain multiplier |
|
0089 |
597 |
|
C axis servo loop gain multiplier |
|
0090 |
0 |
|
gain factor of d/a converter |
|
0091 |
10 |
|
|
|
0094 |
15000 |
|
T axis rapid traverse speed in auto |
|
0095 |
2160 |
|
C axis feed rate in auto mode (30-15000 counts) |
|
0098 |
1100 |
|
T axis accel/decel time constant in auto |
|
0100 |
1 |
|
X axis accel/decel time constant in manual |
|
0101 |
1 |
|
Y axis accel/decel time constant in manual |
|
0102 |
70 |
|
T axis accel/decel time constant in manual |
|
0105 |
200 |
|
accel/decel time constant in contour mode |
|
0106 |
300 |
|
max feedrate |
|
0114 |
500 |
|
slow speed during reference, 500 max. Too slow and axis wont reference ( 91 alarm) |
|
0118 |
0 |
|
C axis backlash amount. |
|
0124 |
0 |
|
X axis amount of velos of drift comp. in servo loop |
|
0125 |
0 |
|
Y axis amount of velos of drift comp. in servo loop |
|
0126 |
0 |
|
T axis amount of velos of drift comp. in servo loop |
|
0127 |
3 |
|
C1 (4th axis) amount of velos of drift comp. in servo loop |
|
0143 |
1010 |
|
X minus software limit |
|
0144 |
3371 |
|
Y minus software limit |
|
0147 |
-49010 |
|
X plus software limit. |
|
0148 |
-39001 |
|
Y plus software limit. |
|
0167 |
200 |
|
accel/decel ramp data (inch) |
|
0168 |
500 |
|
accel/decel ramp data (inch) |
|
0169 |
1000 |
|
accel/decel ramp data (inch) |
|
0170 |
3000 |
|
accel/decel ramp data (inch) |
|
0171 |
5000 |
|
accel/decel ramp data (inch) |
|
0172 |
10000 |
|
accel/decel ramp data (inch) |
|
0300 |
00010010 |
bit 1 |
= 1 enables G31 |
|
0301 |
00000010 |
|
|
|
0302 |
00000001 |
bit 0 |
= 1 micron type auto-index. |
|
|
|
|
= 0 old style auto-index. |
|
0303 |
00000001 |
|
|
|
0304 |
00000000 |
|
|
|
0305 |
01100000 |
bit 6 |
= 1 param. 444 sets TPF 9. |
|
00000010 |
bit 1 |
= 0 T code on same line with X, Y coordinate (non-auto index machines) |
|
|
|
|
|
= 1 T code on separate line (auto-index machines) |
|
|
|
bit 3 |
= 1 M02, M30, M99 not counted as program end (looks for %) |
|
0307 |
00001100 |
|
|
|
0308 |
01000000 |
|
|
|
0309 |
00001111 |
bit 0 |
= 1 automatic coordinate system is effective for X axis |
|
|
|
bit 1 |
= 1 automatic coordinate system is effective for Y axis |
|
|
|
bit 2 |
= 1 automatic coordinate system is effective for T axis |
|
|
|
bit 3 |
= 1 automatic coordinate system is effective for C axis |
|
00000101 |
|
Characteristics for 0310 to 0313 |
|
|
00100101 |
bit 5 |
= 1 DC1 - DC4 codes not used. |
|
|
0312 |
00000101 |
|
= 0 DC1 - DC4 codes used. |
|
0313 |
00000101 |
bit 4 |
= 1 2 stop bits |
|
|
|
|
= 0 1 stop bit |
|
|
|
bit 0-3 |
set baud rate for 1/0 interface, see parameters 0340 -341 |
|
Baud |
3 |
2 |
1 |
0 |
|
50 |
0 |
0 |
0 |
0 |
|
100 |
0 |
0 |
0 |
1 |
|
110 |
0 |
0 |
1 |
0 |
|
150 |
0 |
0 |
1 |
1 |
|
200 |
0 |
1 |
0 |
0 |
|
300 |
0 |
1 |
0 |
1 |
|
600 |
0 |
1 |
1 |
0 |
|
1200 |
0 |
1 |
1 |
1 |
|
2400 |
1 |
0 |
0 |
0 |
|
4800 |
1 |
0 |
0 |
1 |
|
9600 |
1 |
0 |
1 |
0 |
|
0316 |
00011000 |
|
selects resolver as feedback device for C axis |
|
0317 |
00001110 |
|
|
|
11100000 |
bit 5 |
= 1 display of macro contents suppressed while running program |
|
|
|
|
|
= 0 macro contents displayed while running program |
|
|
. |
bit 6 |
= 1 single stepping through macro disabled |
|
|
|
|
= 0 single stepping enabled |
|
|
|
bit 7 |
= 1 programs in 9000 series are locked, cannot be loaded or edited |
|
|
|
|
= 0 programs in 9000 series can be loaded or edited. |
|
0319 |
10000001 |
bit 7 |
same as param. 0318 for 8000 series programs |
|
0323 |
0 |
|
= 0 separate movement of axes (T moves 1st ) |
|
|
|
|
= 31 G31 in program calls macro 9010 program for simultaneous axis movement with T code on same line as X and Y. T code on separate line still works. |
|
0324 |
82 |
|
custom macro call |
|
0325 |
83 |
|
custom macro call |
|
0326 |
84 |
|
custom macro call |
|
2 |
|
Input Device |
|
|
|
|
|
0 = tape reader |
|
|
|
|
1 = ASR-43 (set baud in param. 310) |
|
|
|
|
2 = RS-232 (set baud in param. 311) |
|
|
|
|
3 = RS-232 (set baud in param. 312) |
|
|
|
|
4 = RS-232 (set baud in param. 313) |
|
0341 |
2 |
|
Output Device |
|
|
|
|
0 = Facit 4070 punch |
|
|
|
|
1 = ASR-43 (set baud in param. 310) |
|
|
|
|
2 = RS-232 (set baud in param. 311) |
|
|
|
|
3 = RS-232 (set baud in param. 312) |
|
|
|
|
4 = RS-232 (set baud in param. 313) |
|
0342 |
500 |
|
|
|
0347 |
----- |
|
C2 (5th axis) grid shift (home position offset) varies |
|
0348 |
400 |
|
|
|
0365 |
2000 |
|
C1/C2 maximum deviation permitted (setting max is 2200). |
|
0366 |
1500 |
|
C axis related |
|
0375 |
121920 |
|
absolute preset at home for X axis (metric) |
|
0376 |
96520 |
|
absolute preset at home for Y axis (metric) |
|
0379 |
48000 |
|
absolute preset at home for X axis (inch) |
|
0380 |
38000 |
|
absolute preset at home for Y axis (inch) |
|
0390 |
----- |
|
T06 A-1 tool offset varies |
|
0394 |
----- |
|
T16 A-1 tool offset varies |
|
0398 |
----- |
|
T28 A-1 tool offset varies |
|
0420 |
10011100 |
|
|
|
0421 |
10101001 |
bit 0 |
= 0 4th axis used for C axis |
|
|
|
|
= 1 5th axis used for C axis |
|
0422 |
00000000 |
|
C axis servo loop gain multiplier |
|
0423 |
10000000 |
|
|
|
0424 |
00000010 |
|
|
|
0425 |
81 |
|
sets M81 code (post-punch delay on) |
|
0426 |
82 |
|
sets M82 code (post-punch delay off) |
|
0427 |
3 |
|
|
|
0428 |
4 |
|
|
|
0429 |
12 |
|
M code for nibble start (coordinate nibble) |
|
0430 |
13 |
|
M code for nibble end (coordinate nibble) |
|
0436 |
----- |
|
delay from punch end switch to clutch dump varies |
|
0437 |
150 |
|
|
|
0438 |
100 |
|
delay before punch in milliseconds |
|
0439 |
100 |
|
M81 post-punch delay time in milliseconds |
|
0444 |
----- |
|
delay from clutch dump to brake on varies |
|
0452 |
7000 |
|
X axis position loop gain |
|
0453 |
5600 |
|
Y axis position loop gain |
|
0454 |
4000 |
|
T axis position loop gain |
|
0455 |
3400 |
|
C axis position loop gain |
|
0456 |
800 |
|
X rapid traverse rate (manual) |
|
0457 |
800 |
|
Y rapid traverse rate (manual) |
|
0458 |
6500 |
|
T rapid traverse rate (manual) |
|
0459 |
1200 |
|
|
|
0460 |
160 |
|
jog ramp parameters |
|
0461 |
160 |
|
jog ramp parameters |
|
0462 |
450 |
|
jog ramp parameters |
|
0463 |
0 |
|
|
|
0464 |
3000 |
|
T axis jog feedrate |
|
0465 |
0 |
|
|
|
0466 |
1100 |
|
T axis reference speed |
|
0467 |
50 |
|
C axis low speed rate during reference point return (FL speed) |
|
0468 |
1300 |
|
max. nibble bite for G68/G69 metric 1-9999 (.01 mm) |
|
0469 |
510 |
|
max. Nibble bite for G68/G69 inch 1-9999 (.001") |
|
0470 |
1300 |
|
maximum nibble feedrate (Q) - metric value |
|
0471 |
510 |
|
maximum nibble feedrate (Q) - inch value |
|
0472 |
508 |
|
accel/decel ramp data (metric) |
|
0473 |
1270 |
|
accel/decel ramp data (metric) |
|
0474 |
2540 |
|
accel/decel ramp data (metric) |
|
0475 |
7620 |
|
accel/decel ramp data (metric) |
|
0476 |
12700 |
|
accel/decel ramp data (metric) |
|
0477 |
25400 |
|
accel/decel ramp data (metric) |
|
0478-0483 |
3000 |
|
rapid traverse speeds X axis |
|
0484 |
3200 |
|
rapid traverse speeds X axis |
|
0485 |
40 |
|
0 - .2 inch ramp |
|
0486 |
135 |
|
.2 - .5 inch ramp |
|
0487 |
135 |
|
.5 - 1 inch ramp |
|
0488 |
175 |
|
1 - 3 inch ramp |
|
0489 |
180 |
|
3 - 5 inch ramp |
|
0490 |
200 |
|
5 - 10 inch ramp |
|
0491 |
390 |
|
10+ inch ramp |
|
0492-0497 |
3000 |
|
rapid traverse speeds Y axis |
|
0498 |
3200 |
|
rapid traverse speeds Y axis |
|
0499 |
40 |
|
0 - .2 inch ramp |
|
0500 |
155 |
|
.2 - .5 inch ramp |
|
0501 |
165 |
|
.5 - 1 inch ramp |
|
0502 |
175 |
|
1 - 3 inch ramp |
|
0503 |
180 |
|
3 - 5 inch ramp |
|
0504 |
200 |
|
5 - 10 inch ramp |
|
0505 |
390 |
|
10+ inch ramp |
|
0506 |
127 |
|
|
|
0507 |
50 |
|
10 = .010 inch, sets back-out of work clamps during prog. move will accept max. of 4.0 inches. Only active with G75, not 03/M04. |
|
0510-0515 |
35 |
|
X axis punch anticipation |
|
0516 |
0 |
|
|
|
0517-0523 |
35 |
|
Y axis punch anticipation |
|
0540 |
1 |
|
T axis tool station at home |
|
0541 |
33 |
|
number of turret stations |
|
0542 |
1 |
|
T command for station 1 |
|
0543 |
2 |
|
T command for station 2 |
|
0544 to |
3 to |
|
T command for station 3 to |
|
0574 |
33 |
|
T command for station 33 |
|
0768-0771 |
1250 |
|
1.5" station tool offsets |
|
0772 |
0 |
|
|
|
0773-0776 |
1250 |
|
1.5" station tool offsets |
|
0777 |
0 |
|
|
|
0778-0781 |
1250 |
|
1.5" station tool offsets |
|
0782 |
0 |
|
|
|
0783-0787 |
1250 |
|
1.5" station tool offsets |
|
0788 |
0 |
|
|
|
0789-0793 |
1250 |
|
1.5" station tool offsets |
|
0794 |
0 |
|
|
|
0795-0799 |
1250 |
|
1.5" station tool offsets |
|
0800-0842 |
0 |
|
|
|
0843 |
25600 |
|
positioning counts for T02 |
|
0844 |
3840 |
|
positioning counts for T03 |
|
0845 |
51200 |
|
positioning counts for T04 |
|
0846 |
64000 |
|
positioning counts for T05 |
|
0847 |
89600 |
|
positioning counts for T06 |
|
0848 |
115200 |
|
positioning counts for T07 |
|
0849 |
128000 |
|
positioning counts for T08 |
|
0850 |
140800 |
|
positioning counts for T09 |
|
0851 |
153600 |
|
positioning counts for T10 |
|
0852 |
179200 |
|
positioning counts for T11 |
|
0853 |
204800 |
|
positioning counts for T12 |
|
0854 |
217600 |
|
positioning counts for T13 |
|
0855 |
230400 |
|
positioning counts for T14 |
|
0656 |
243200 |
|
positioning counts for T15 |
|
0857 |
268800 |
|
positioning counts for T16 |
|
0858 |
294400 |
|
positioning counts for T17 |
|
0859 |
307200 |
|
positioning counts for T18 |
|
0860 |
320000 |
|
positioning counts for T19 |
|
0861 |
332000 |
|
positioning counts for T20 |
|
0862 |
345600 |
|
positioning counts for T21 |
|
0863 |
371200 |
|
positioning counts for T22 |
|
0864 |
396600 |
|
positioning counts for T23 |
|
0865 |
409600 |
|
positioning counts for T24 |
|
0866 |
422400 |
|
positioning counts for T25 |
|
0867 |
435200 |
|
positioning counts for T26 |
|
0868 |
448000 |
|
positioning counts for T27 |
|
0869 |
473600 |
|
positioning counts for T28 |
|
0870 |
499200 |
|
positioning counts for T29 |
|
0871 |
512000 |
|
positioning counts for T30 |
|
0872 |
524800 |
|
positioning counts for T31 |
|
0873 |
537600 |
|
positioning counts for T32 |
|
0874 |
550400 |
|
positioning counts for T33 |
|
0917-0949 |
----- |
|
counter for hits on each tool (0917=T01, 0918 = T02, etc.) varies |
|
0992 |
576000 |
|
encoder counts for turret revolution |
|
0993 |
0 |
|
|
|
0994 |
2 |
|
C2 (5th axis) amount of velos of drift comp. in servo loop |
|
0995 |
1500 |
|
C axis maximum feedrate in nibble mode (1-9999, 1 unit =.01 degree). |
|
0997 and up |
not used |
|
|